6063 grade is commonly referred to as the architectural alloy. It was developed as an extrusion alloy with relatively high tensile properties, excellent finishing characteristics and a high degree of resistance to corrosion. This alloy is most often found in various interior and exterior architectural applications, such as windows, doors, store fronts and assorted trim items. It is the alloy best suited for anodizing applications - either plain or in a variety of colors.

6063-T52
Extruded Stock Lengths 21 "1" (Sharp Inside and Outside Corners)
AMS-QQ-A-200/9
Request Information
Unit of Measure
Items
Tubing6

Aluminum Rectangular Tubing
Tubing6

Aluminum Rectangular Tubing
Tubing6

Aluminum Rectangular Tubing
Tubing6

Aluminum Rectangular Tubing
Tubing6

Aluminum Rectangular Tubing
Material N/A Aluminum
Shapeform N/A Rectangular Tubing
Series N/A 6063-T52
Grade N/A 6063
Temper N/A T52
Size N/A 1/2 x 1 x 0.125 inches N/A 3/4 x 1 1/2 x 0.125 inches N/A 1 x 1 1/2 x 0.125 inches N/A 1 X 2 X 0.125 inches N/A 1 x 3 x 0.125 inches
Working Decimal Equivalent N/A 0.500 x 1.000 x 0.125 inches12.7 x 25.4 x 3.175 mm N/A 0.750 x 1.500 x 0.125 inches19.05 x 38.1 x 3.175 mm N/A 1.000 x 1.500 x 0.125 inches25.4 x 38.1 x 3.175 mm N/A 1.000 x 2.000 x 0.125 inches25.4 x 50.8 x 3.175 mm N/A 1.000 x 3.000 x 0.125 inches25.4 x 76.2 x 3.175 mm
Width N/A 1/2 inches N/A 3/4 inches N/A 1 inches N/A 1 inches N/A 1 inches
Length N/A 1 inches N/A 1 1/2 inches N/A 1 1/2 inches N/A 2 inches N/A 3 inches
Height N/A 0.125 inches
Estimated Weight N/A 0.3638 lbs/ft0.5413940632 kg/m N/A 0.5820 lbs/ft0.866111448 kg/m N/A 0.6548 lbs/ft0.9744497872 kg/m N/A 0.8003 lbs/ft1.1909776492 kg/m N/A 1.0913 lbs/ft1.6240333732 kg/m
Estimated Weight 12' 1" N/A 7.670 lbs3.479112 kg N/A 12.271 lbs5.5661256 kg N/A 13.805 lbs6.261948 kg N/A 16.873 lbs7.6535928 kg N/A 23.008 lbs10.4364288 kg
ASTM Specification N/A AMS-QQ-A-200/9
Ultimate Strength N/A 27 ksi
Yield Strength N/A 21 ksi
Elongation percent in 2 inches N/A 12
Hardness Brinnel Number
N/A 60
Ultimate Shearing Strength N/A 17 ksi
Fatigue Endurance Limit1 N/A 10 ksi
Modulus of Elasticity2 N/A 10.0 x 103 ksi
Resistance to Corrosion - General3 N/A A
Stress Corrosion Cracking N/A A
Workability (Cold) N/A B
Mechinability N/A C
Brazeability4 N/A A
Gas Weldability5 N/A A
Arc Weldability6 N/A A
Resistance Spot and Seam Weldability7 N/A A
Applications N/A Pipe railing, furniture, architectural extrusions
Density N/A 0.097 lbs/in³
Specific Gravity N/A 2.70
  • 1 Based on 500,000.000 cycles of completely reversed stress using the R. R. Moore-type of machine and specimen.
  • 2 Average of tension and compression moduli. Compression modulus is about 2 percent greater than tension modulus.
  • 3 Ratings A through E are relative ratings in decreasing order of merit, based on exposures to sodium chloride solution by intermittent spraying or immersion. Alloys with A and B ratings can be used in industrial and seacoast atmospheres without protection. Alloys with C, D and E ratings generally should be protected at least on faying surfaces.
  • 4 Ratings A through D for Weldability and Brazeability are relative ratings.
  • 5 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.
  • 6 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.
  • 7 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.