Item # 301-093-24-A, Stainless Steel Coil and Strip On Continental Steel & Tube Co.

All Categories > Stainless Steel > Stainless Steel Sheet and Coil > Stainless Steel Coil and Strip > Item # 301-093-24-A


	Item # 301-093-24-A, Stainless Steel Coil and Strip

Austenitic (Chrome Nickel)
Good Cold Working
Good Elongation in Full Hard Condition
Good Fatigue Life
High Strength to Weight Ratio
Work Hardens Readily - so is in demand in harder tempers
Not Heat-treatable for Hardening Purposes
Non-magnetic in Annealed Condition
Slightly Magnetic in Work-hardened Condition
Good Heat and Corrosion Resistance
Welds Easily
Solution Annealed by Cooling Rapidly from 2000°F in Air or Water.

Unit of Measure: Imperial

Specifications · Typical Mechanical Properties · Comparative Characteristics and Applications · Applications

Specifications

Material		Type 301 Stainless Steel

Shapeform		Coil & Strip

Thickness		0.093 inches

Maximum Coil Width		24 inches

Strip Weight per Unit Area		3.8837 lbs/ft²

Weight		7.76736 lbs/ft

Temper		Annealed

Nominal Composition		0.03% Max. Sulphur 0.045% Max. Phosphorus 0.10% Nitrogen 0.15% Max. Carbon 1.00% Max. Silicon 16.00 to 18.00% Chrominum 2.00% Max. Manganese 6.00 to 8.00% Nickel

ASTM Specification		ASTM A240 ASTM A262 Prac E ASTM A480 ASTM A666 UNS S30100

Typical Mechanical Properties

Steel Alloy Group		Austenitic

Magnetic Properties		Non-Magnetic

Harden By		Cold Work

Corrosion Resistance		High

Hardness		Low to Med.

Strength		Low to Med.

Ductility		High

Toughness		High

Elec. Conductance		Low

Thermal Conductance		Low

Thermal Expansion		High

Heat Resistance (Scaling Strength)		High/High

Comparative Characteristics and Applications

Yield Strength		43000 lbs/in²

Tensile Strength		106000 lbs/in²

Elongation percent in 2 inches		56 %

Hardness (Rockwell B)		86

Density		0.29 lbs/in³

Modulus of Elasticity in Tension		28.0 x 10⁶ lbs/in²

Specific Heat (32 to 212°F)		0.12 BTU/ºF/lbs

Thermal Conductivity at 212°F		9.4 BTU/hr.ft²/ft/ºF

Thermal Conductivity at 932°F		12.4 BTU/hr.ft²/ft/ºF

Mean Coefficient of Thermal Expansion per °F (32 to 212°F)		9.4 x 10^-6 ºF

Mean Coefficient of Thermal Expansion per °F (32 to 600°F)		9.5 x 10^-6 ºF

Mean Coefficient of Thermal Expansion per °F (32 to 1000°F)		10.1 x 10^-6 ºF

Mean Coefficient of Thermal Expansion per °F (32 to 1200°F)		10.4 x 10^-6 ºF

Melting Point Range		2550 to 2590 ºF

Electrical Resistivity		69 µΩ.cm

Max. Operating Temp. (Continuous Service)		1600 ºF

Max. Operating Temp. (Intermittent Service)		1500 ºF

Welding Properties		Very Good-Tough Welds

Drawing and Stamping		Good

Hot Working - Initial Forging		2100 to 2300 ºF

Annealing Temp.		1850 to 2050 ºF

Stress Relieving Temp.		400 to 750 ºF

Applications

Rapid transit cars, buses, aircraft, cargo containers
Retractor springs
Hose clamps
Conveyors
Bottling machinery
Jewelry
Cryogenic vessels and components
Still tubes
Expand metal parts
Mixing bowls
Dryers
Furnace parts
Heat exchangers
Paper mill equipment
Oil refining equipment
Textile industry
Dyeing equipment
Jet engine parts
Welded storage tanks for organic chemicals
Combustion chambers
Furnace arch supports
Kiln linings
Smoke control ductwork
Coal chutes
Gauge parts
Cutlery
Fish hooks
Glass molds
Bank vaults
Fasteners
Skewers
Dairy industry
Burner and emission control components
Recuperators
Pipes, tubes

DOWNLOADS


		Terminology Sheet

		Carbon Steel Mill Edge Hot Rolled Strip (JPG, 41KB)

		Types Finishes Spec Sheet

Item # 301-093-24-A, Stainless Steel Coil and Strip

Material

Shapeform

Thickness

Maximum Coil Width

Strip Weight per Unit Area

Weight

Temper

Nominal Composition

ASTM Specification

Steel Alloy Group

Magnetic Properties

Harden By

Corrosion Resistance

Hardness

Strength

Ductility

Toughness

Elec. Conductance

Thermal Conductance

Thermal Expansion

Heat Resistance (Scaling Strength)

Yield Strength

Tensile Strength

Elongation percent in 2 inches

Hardness (Rockwell B)

Density

Modulus of Elasticity in Tension

Specific Heat (32 to 212°F)

Thermal Conductivity at 212°F

Thermal Conductivity at 932°F

Mean Coefficient of Thermal Expansion per °F (32 to 212°F)

Mean Coefficient of Thermal Expansion per °F (32 to 600°F)

Mean Coefficient of Thermal Expansion per °F (32 to 1000°F)

Mean Coefficient of Thermal Expansion per °F (32 to 1200°F)

Melting Point Range

Electrical Resistivity

Max. Operating Temp. (Continuous Service)

Max. Operating Temp. (Intermittent Service)

Welding Properties

Drawing and Stamping

Hot Working - Initial Forging

Annealing Temp.

Stress Relieving Temp.