Continental Steel and Tube Company
Continental Steel and Tube Company
P.O. BOX 030040
Fort Lauderdale, FL, 33303
Phone: 954.332.2290
Fax: 954.332.2296
Email: Sales@ContinentalSteel.com
Website: www.continentalsteel.com
Print Back
2024 is one of the best known of the high strength aluminum alloys. With its high strength and excellent fatigue resistance, it is used to advantage on structures and parts where good strength-to-weight ratio is desired. It is readily machined to a high finish. It is readily formed in the annealed condition and may be subsequently heat treated. Arc or gas welding is generally not recommended, although this alloy may be spot, seam or flash welded. Since corrosion resistance is relatively low, 2024 is commonly used with an anodized finish or in clad form ("Alclad") with a thin surface layer of high purity aluminum. Applications: aircraft structural components, aircraft fittings, hardware, truck wheels and parts for the transportation industry

2024-T351
AMS-OQ-A-225/5 AMS 4120 ASTM B211 UNS A92024
Unit of Measure

Specifications

Material

 N/A Aluminum

Shapeform

 N/A Rectangles

Series

 N/A 2024-T351

Grade

 N/A 2024

Temper

 N/A T351

Size

 N/A 3 x 5 inches

Working Decimal Equivalent

 N/A 3.000 x 5.000 inches76.2 x 127 mm

Width

 N/A 3 inches

Length

 N/A 5 inches

Estimated Weight

 N/A 18.0 lbs/ft26.786952 kg/m

Estimated Weight per 12' Bar

 N/A 216.000 lbs97.9759584 kg

ASTM Specification

 N/A AMS 4120 AMS-QQ-A-225/6 ASTM B211 UNS A92024

Density

 N/A 0.100 lbs/in³

Specific Gravity

 N/A 2.78

Typical Mechanical Properties

Ultimate Strength

 N/A 68 ksi

Yield Strength

 N/A 47 ksi

Elongation percent in 2 inches

 N/A 20

Hardness Brinnel Number

 N/A 120

Ultimate Shearing Strength

 N/A 41 ksi
Fatigue Endurance Limit1 N/A 20 ksi
Modulus of Elasticity2 N/A 10.6 x 104 ksi

Comparative Characteristics and Applications

Resistance to Corrosion - General3 N/A D
Stress Corrosion Cracking4 N/A C
Workability (Cold)5 N/A C

Mechinability

 N/A B
Brazeability6 N/A D
Gas Weldability7 N/A C
Arc Weldability8 N/A B
Resistance Spot and Seam Weldability9 N/A B

Applications

 N/A Truck wheels, screw machine products, aircraft structures

Aluminum Alloy Designations

N/A

    The aluminum industry uses a four-digit index system for the designation of its wrought aluminum alloys.
    As outlined below, the first digit indicates the alloy group according to the major alloying elements.

    1xxx Series
    In this group minimum aluminum content is 99% and there is no major alloying element. The second digit indicates modifications in impurity limits. If the second digit is zero, there is no special control on individual impurities. Digits 1 through 9, which are assigned consecutively as needed, indicate special control of one or more individual impurities. The last two digits indicate specific minimum aluminum content. Although the absolute minimum aluminum content in this group is 99%, the minimum for certain grades is higher than 99%, and the last two digits represent the hundredths of a per cent over 99. Thus, 1030 would indicate 99.30% minimum aluminum. without special control on individual impurities. The designations 1130, 1230, 1330, etc.. indicate the same purity with special control on one or more impurities. Likewise 1100 indicates minimum aluminum content of 99.00% with individual impurity control.

    2xxx through 9xxx Series
    The major alloying elements are indicated by the first digit, as follows:
      2xxx Copper
      3xxx Manganese
      4xxx Silicon
      5xxx Magnesium
      6xxx Magnesium and silicon
      7xxx Zinc
      8xxx Other element
      9xxx Unused series

    The second digit indicates alloy modification. If the second digit is zero. it indicates the original alloy: digits 1 through 9, which are assigned consecutively, indicate alloy modifications. The last two digits have no special significance, serving only to identify the different alloys in the group.

    Experimental Alloys
    Experimental alloys are designated according to the four digit system, but they are prefixed by the letter X. The prefix is dropped when the alloy becomes standard. During development, and before they are designated as experimental, new alloys are identified by serial numbers assigned by their originators. Use of the serial number is discontinued when the X number is assigned.
  • 1 Based on 500,000.000 cycles of completely reversed stress using the R. R. Moore-type of machine and specimen.
  • 2 Average of tension and compression moduli. Compression modulus is about 2 percent greater than tension modulus.
  • 3 Ratings A through E are relative ratings in decreasing order of merit, based on exposures to sodium chloride solution by intermittent spraying or immersion. Alloys with A and B ratings can be used in industrial and seacoast atmospheres without protection. Alloys with C, D and E ratings generally should be protected at least on faying surfaces.
    In relatively thick sections, the rating would be E
  • 4 Stress-corrosion cracking ratings are based on service experience and on laboratory tests of specimens exposed to the 3.5% sodium chloride alternate immersion test.
  • 5 Ratings A through D for Workability (cold), and A through E for Machinability, are relative ratings in decreasing order of merit.
  • 6 Ratings A through D for Weldability and Brazeability are relative ratings.
  • 7 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.
  • 8 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.
  • 9 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.