| Items |
 304-125-500 Rectangular Stainless Steel Bar - Type 304 |
304-125-625 Rectangular Stainless Steel Bar - Type 304 |
304-125-750 Rectangular Stainless Steel Bar - Type 304 |
304-125-1000 Rectangular Stainless Steel Bar - Type 304 |
304-125-1250 Rectangular Stainless Steel Bar - Type 304 |
|||||
| Material | Type 304 Stainless Steel | |||||||||
| Shapeform | Rectangular Bar | |||||||||
| Thickness x Width | 1/8 x 1/2 inches | 1/8 x 5/8 inches | 1/8 x 3/4 inches | 1/8 x 1 inches | 1/8 x 1 1/4 inches | |||||
| Working Decimal Equivalent | 0.125 x 0.500 inches3.175 x 12.700 mm | 0.125 x 0.625 inches3.175 x 15.875 mm | 0.125 x 0.750 inches3.175 x 19.050 mm | 0.125 x 1.000 inches3.175 x 25.400 mm | 0.125 x 1.250 inches3.175 x 31.750 mm | |||||
| Thickness | 1/8 inches | |||||||||
| Width | 1/2 inches | 5/8 inches | 3/4 inches | 1 inches | 1 1/4 inches | |||||
| Weight | 0.2126 lbs/ft0.3163488 kg/m | 0.2657 lbs/ft0.3953616 kg/m | 0.3188 lbs/ft0.4743744 kg/m | 0.4251 lbs/ft0.6325488 kg/m | 0.5314 lbs/ft0.7907232 kg/m | |||||
| Weight per 12' Length | 2.551 lbs1.155603 kg | 3.188 lbs1.444164 kg | 3.826 lbs1.733178 kg | 5.101 lbs2.310753 kg | 6.377 lbs2.888781 kg | |||||
| Finish | No. 2B | |||||||||
| Condition | Annealed Pickled | |||||||||
| Nominal Composition | 0 to 0.25% Carbon 1.00% Max. Silicon 2.00% Max. Manganese 6 to 36% Nickel 7 to 30% Chrome | |||||||||
| ASTM Specification | ASTM A276 UNS S30400 | |||||||||
| Random Length | 10 to 14 ft | |||||||||
| Steel Alloy Group | Austenitic | |||||||||
| Magnetic Properties | Non-Magnetic | |||||||||
| Harden By | Cold Work | |||||||||
| Corrosion Resistance | High | |||||||||
| Hardness | Low to Med. | |||||||||
| Strength | Low to Med. | |||||||||
| Ductility | High | |||||||||
| Toughness | High | |||||||||
| Elec. Conductance | Low | |||||||||
| Thermal Conductance | Low | |||||||||
| Thermal Expansion | High | |||||||||
| Heat Resistance (Scaling Strength) | High/High | |||||||||
| Yield Strength | 46000 lbs/in² | |||||||||
| Tensile Strength | 89000 lbs/in² | |||||||||
| Elongation percent in 2 inches | 55 % | |||||||||
| Hardness (Rockwell B) | 86 | |||||||||
| Creep Strength Load for 10000 Hr. with 1% Elongation at 1000°F | 17000 lbs/in² | |||||||||
| Creep Strength Load for 10000 Hr. with 1% Elongation at 1100°F | 12000 lbs/in² | |||||||||
| Creep Strength Load for 10000 Hr. with 1% Elongation at 1200°F | 7000 lbs/in² | |||||||||
| Creep Strength Load for 10000 Hr. with 1% Elongation at 1300°F | 4000 lbs/in² | |||||||||
| Density | 0.29 lbs/in³ | |||||||||
| Modulus of Elasticity in Tension | 28.0 x 106 lbs/in² | |||||||||
| Specific Heat (32 to 212°F) | 0.12 BTU/ºF/lbs | |||||||||
| Thermal Conductivity at 212°F | 9.4 BTU/hr.ft²/ft/ºF | |||||||||
| Thermal Conductivity at 932°F | 12.4 BTU/hr.ft²/ft/ºF | |||||||||
| Mean Coefficient of Thermal Expansion per °F (32 to 212°F) | 9.6 x 10-6 ºF | |||||||||
| Mean Coefficient of Thermal Expansion per °F (32 to 600°F) | 9.9 x 10-6 ºF | |||||||||
| Mean Coefficient of Thermal Expansion per °F (32 to 1000°F) | 10.2 x 10-6 ºF | |||||||||
| Mean Coefficient of Thermal Expansion per °F (32 to 1200°F) | 10.4 x 10-6 ºF | |||||||||
| Melting Point Range | 2550 to 2650 ºF | |||||||||
| Electrical Resistivity | 72 µΩ.cm | |||||||||
| Max. Operating Temp. (Continuous Service) | 1650 ºF | |||||||||
| Max. Operating Temp. (Intermittent Service) | 1500 ºF | |||||||||
| Welding Properties | Very Good-Tough Welds | |||||||||
| Drawing and Stamping | Very Good | |||||||||
| Hot Working - Initial Forging | 2100 to 2300 ºF | |||||||||
| Annealing Temp. | 1850 to 2050 ºF | |||||||||
| Stress Relieving Temp. | 400 to 750 ºF | |||||||||
| Applications |
|
|||||||||
|
|
||||||||||
