Aluminum Rounds - Seires 7075

7075 is one of the highest strength aluminum alloys available Its strength-to weight ratio is excellent and it is ideally used for highly stressed parts. It may be formed in the annealed condition and subsequently heat treated. Spot or flash welding can be used, although arc and gas welding are not recommended. It is available in the clad ('Alclad") form to improve the corrosion resistance with the over-all high strength being only moderately affected. Applications: Used where highest strength is needed

7075-T6
AMS-QQ-A-225/9 AMS4122T6 AMS 4123 T651
ASTM B211 UNS A97075

Request Information Search by Specification

Unit of Measure

Items	7075-T6-375 Aluminum Rounds - Seires 7075	7075-T6-500 Aluminum Rounds - Seires 7075	7075-T651-625 Aluminum Rounds - Seires 7075	7075-T651-750 Aluminum Rounds - Seires 7075	7075-T651-1000 Aluminum Rounds - Seires 7075
Material	N/A Aluminum
Shapeform	N/A Round
Series	N/A 7075-T6	N/A 7075-T6	N/A 7075-T651	N/A 7075-T651	N/A 7075-T651
Grade	N/A 7075
Temper	N/A T6	N/A T6	N/A T651	N/A T651	N/A T651
Diameter	N/A 3/8 inches	N/A 1/2 inches	N/A 5/8 inches	N/A 3/4 inches	N/A 1 inches
Diameter	N/A 0.375 inches9.525 mm	N/A 0.5 inches12.7 mm	N/A 0.625 inches15.875 mm	N/A 0.75 inches19.05 mm	N/A 1 inches25.4 mm
Estimated Weight	N/A 0.1339 lbs/ft0.1992651596 kg/m	N/A 0.2380 lbs/ft0.354183032 kg/m	N/A 0.3718 lbs/ft0.5532993752 kg/m	N/A 0.5354 lbs/ft0.7967630056 kg/m	N/A 0.9591 lbs/ft1.4272980924 kg/m
Estimated Weight per 12' Bar	N/A 1.606 lbs0.7284693944 kg	N/A 2.856 lbs1.2954598944 kg	N/A 4.462 lbs2.0239292888 kg	N/A 6.425 lbs2.91433117 kg	N/A 11.423 lbs5.1813859852 kg
ASTM Specification	N/A AMS 4122 AMS-QQ-A-225/9 ASTM B211 UNS A97075	N/A AMS 4122 AMS-QQ-A-225/9 ASTM B211 UNS A97075	N/A AMS 4123 AMS-QQ-A-225/9 ASTM B211 UNS A97075	N/A AMS 4123 AMS-QQ-A-225/9 ASTM B211 UNS A97075	N/A AMS 4123 AMS-QQ-A-225/9 ASTM B211 UNS A97075
Ultimate Strength	N/A 83 ksi
Yield Strength	N/A 73 ksi
Elongation percent in 2 inches	N/A 11
Hardness Brinnel Number	N/A 150
Ultimate Shearing Strength	N/A 48 ksi
Fatigue Endurance Limit¹	N/A 23 ksi
Modulus of Elasticity²	N/A 10.4 x 10⁴ ksi
Resistance to Corrosion - General³	N/A C
Stress Corrosion Cracking⁴	N/A C
Workability (Cold)⁵	N/A D
Mechinability	N/A B
Brazeability⁶	N/A D
Gas Weldability⁷	N/A D
Arc Weldability⁸	N/A D
Resistance Spot and Seam Weldability⁹	N/A B
Applications	N/A Aircraft and other structures
Density	N/A 0.101 lbs/in³
Specific Gravity	N/A 2.81
¹ Based on 500,000.000 cycles of completely reversed stress using the R. R. Moore-type of machine and specimen. ² Average of tension and compression moduli. Compression modulus is about 2 percent greater than tension modulus. ³ Ratings A through E are relative ratings in decreasing order of merit, based on exposures to sodium chloride solution by intermittent spraying or immersion. Alloys with A and B ratings can be used in industrial and seacoast atmospheres without protection. Alloys with C, D and E ratings generally should be protected at least on faying surfaces. In relatively thick sections, the rating would be E ⁴ Stress-corrosion cracking ratings are based on service experience and on laboratory tests of specimens exposed to the 3.5% sodium chloride alternate immersion test. ⁵ Ratings A through D for Workability (cold), and A through E for Machinability, are relative ratings in decreasing order of merit. ⁶ Ratings A through D for Weldability and Brazeability are relative ratings. ⁷ A = Generally weldable by all commercial procedures and methods. B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance. C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties. ⁸ A = Generally weldable by all commercial procedures and methods. B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance. C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties. ⁹ A = Generally weldable by all commercial procedures and methods. B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance. C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.

Products Catalog