3003 is the most widely used of all aluminum alloys. It is essentially commercially pure aluminum with the addition of manganese which increases the strength some 20% over the 1100 grade. Thus, it has all the excellent characteristics of 1100 with higher strength. It has excellent corrosion resistance. It has excellent workability and it may be deep drawn or spun, welded or brazed. It is non heat treatable. Applications: cooking utensils, decorative trim, awnings, siding, storage tanks, chemical equipment.

3003-H16
Mill Finish
AMS-QQ-A-250/2
Request Information
Unit of Measure
Items
506450912-497007203-aluminum-coil-2

Truck Trailer Roof Coil
506450912-497007203-aluminum-coil-2

Truck Trailer Roof Coil
506450912-497007203-aluminum-coil-2

Truck Trailer Roof Coil
506450912-497007203-aluminum-coil-2

Truck Trailer Roof Coil
Material N/A Aluminum
Shapeform N/A Coil
Series N/A 3003-H16
Grade N/A 3003
Temper N/A H16
Finish N/A Mill
Thickness N/A 0.032 inches0.8128 mm N/A 0.032 inches0.8128 mm N/A 0.040 inches1.016 mm N/A 0.040 inches1.016 mm
Size N/A 96.5 x Coil N/A 102.5 x Coil N/A 96.5 x Coil N/A 102.5 x Coil
Width N/A 96.5 N/A 102.5 N/A 96.5 N/A 102.5
Coil Weight per Length N/A 3.669 lbs/ft5.460 kg/m N/A 3.897 lbs/ft5.799 kg/m N/A 4.586 lbs/ft6.825 kg/m N/A 4.871 lbs/ft7.249 kg/m
ASTM Specification N/A AMS-QQ-A-250/2
Ultimate Strength N/A 26 ksi
Yield Strength N/A 25 ksi
Elongation percent in 2 inches N/A 5
Hardness Brinnel Number
N/A 47
Ultimate Shearing Strength N/A 15 ksi
Fatigue Endurance Limit1 N/A 10 ksi
Modulus of Elasticity2 N/A 10.0 x 106 ksi
Resistance to Corrosion - General3 N/A A
Stress Corrosion Cracking4 N/A A
Workability (Cold)5 N/A C
Mechinability N/A D
Brazeability6 N/A A
Gas Weldability7 N/A A
Arc Weldability8 N/A A
Resistance Spot and Seam Weldability9 N/A A
Applications N/A Cooking utensils, chemical equipment, pressure vessels, sheet metal work, builder's hardware, storage tanks
Density N/A 0.099 lbs/in³
Specific Gravity N/A 2.73
  • 1 Based on 500,000.000 cycles of completely reversed stress using the R. R. Moore-type of machine and specimen.
  • 2 Average of tension and compression moduli. Compression modulus is about 2 percent greater than tension modulus.
  • 3 Ratings A through E are relative ratings in decreasing order of merit, based on exposures to sodium chloride solution by intermittent spraying or immersion. Alloys with A and B ratings can be used in industrial and seacoast atmospheres without protection. Alloys with C, D and E ratings generally should be protected at least on faying surfaces.
  • 4 Stress-corrosion cracking ratings are based on service experience and on laboratory tests of specimens exposed to the 3.5% sodium chloride alternate immersion test.
  • 5 Ratings A through D for Workability (cold), and A through E for Machinability, are relative ratings in decreasing order of merit.
  • 6 Ratings A through D for Weldability and Brazeability are relative ratings.
  • 7 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.
  • 8 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.
  • 9 A = Generally weldable by all commercial procedures and methods.
    B = Weldable with special techniques or for specific applications that justify preliminary trials or testing to develop welding procedure and weld performance.
    C = Limited weldability because of crack sensitivity or loss in resistance to corrosion and mechanical properties.